Avalon 2003 Hideaway Bedienungshandbuch

Featuring theBurnerTested and Listed byOMNI-Test Laboratories, Inc.Beaverton, OregonReport # 028-S-53-5ANSI Z21.88• Built-In Direct Vent Fireplace• Na

10 Installation (for qualified installers only)Travis Industries4030612 100-01148Corner InstallationsA typical 45° installationuses the minimum frami

Installation (for qualified installers only) 11Travis Industries 4030612 100-01148Gas Line RequirementsMASSACHUSETTS INSTALLATIONS - WARNING:TH

12 Installation (for qualified installers only)Travis Industries4030612 100-01148Optional Gas Line LocationRemove the two screws near the gas inlet (

Installation (for qualified installers only) 13Travis Industries 4030612 100-01148Electrical Line ConnectionabInsert the sheathed cable from the powe

14 Installation (for qualified installers only)Travis Industries4030612 100-01148Vent Requirements• The gas appliance and vent system must be vented

Installation (for qualified installers only) 15Travis Industries 4030612 100-01148Vent Installation• Slide the vent sections together and turn 1/4 tu

16 Installation (for qualified installers only)Travis Industries4030612 100-01148Approved Vent ConfigurationsRestrictor Position• A vent restrictor i

Installation (for qualified installers only) 17Travis Industries 4030612 100-01148Vent Configurations with Vertical Vent Termination• The termination

18 Installation (for qualified installers only)Travis Industries4030612 100-01148Horizontal Terminations5. Use a single 90°elbow (NOTE:an additional

Installation (for qualified installers only) 19Travis Industries 4030612 100-01148 Termination Requirements (see the illustration below)NOTE : Meas

2 IntroductionTravis Industries 4021122 100-01143IntroductionWe welcome you as a new owner of a Hideaway gas fireplace. In purchasing a Hideaway you

20 Installation (for qualified installers only)Travis Industries4030612 100-01148Hearth RequirementsDo not build a hearth or other item above the bas

Installation (for qualified installers only) 21Travis Industries 4030612 100-01148Facing RequirementsNOTE: The combustible area above the facing must

22 Installation (for qualified installers only)Travis Industries4030612 100-01148Facing - Fireplace Details3/8"1/8"FaceFireplace1"Wall

Installation (for qualified installers only) 23Travis Industries 4030612 100-01148Facing Detail – Drywall FacingNOTE The facing tucks under the notc

24 Installation (for qualified installers only)Travis Industries4030612 100-01148Facing Detail – Tile FacingTileNOTE: Make sure to position the frami

Installation (for qualified installers only) 25Travis Industries 4030612 100-01148Facing Detail –Facing Over 1” Thick (Brick)WARNING: Any facing that

26 Installation (for qualified installers only)Travis Industries4030612 100-01148Mantel Requirements• The combustible area above the facing must not

Finalizing the Installation 27Travis Industries 4030612 100-011481 Remove the glass following the directions below.Warning: The appliance must be comp

28 Finalizing the InstallationTravis Industries 4030612 100-01148• If converting to propane, do so now before installing the logs.8. Install the log

Finalizing the Installation 29Travis Industries 4030612 100-01148Place the right twig as shown. It rests against the firebox liner.The logs should lo

Table of Contents 3Travis Industries 4030612 100-01148IntroductionIntroduction & Important Information...2Safety PrecautionsSafety Pr

30 Finalizing the InstallationTravis Industries 4030612 100-011483 We recommend you purge the gas line at this time (with the glass removed). This al

Finalizing the Installation 31Travis Industries 4030612 100-011487 Check the pilot flame to make sure it looks like the illustration below. Adjust th

32 Finalizing the InstallationTravis Industries 4030612 100-01148FINE TUNING THE EMBER-FYRE™ BURNEREach installation is affected by altitude, vent co

Operation 33Travis Industries 4030612 100-01148Before You Begin• Read this entire manual before you use your new fireplace (especially the section &qu

34 OperationTravis Industries 4030612 100-01148Starting The Pilot FlameThe pilot flame is required to ignite the mainburners (it also plays a safety r

Operation 35Travis Industries 4030612 100-01148Starting the Fireplace for the First Time+ Burn the heater at a high setting with the blower off for an

36 OperationTravis Industries 4030612 100-01148Adjusting the Blower SpeedThe blower helps transfer heat from the heater into the room. It will not tu

Maintenance 37Travis Industries 4030612 100-01148Maintaining Your Fireplace's Appearance• Fingerprints or other marks left on the optional gold s

38 MaintenanceTravis Industries 4030612 100-01148Troubleshooting TableProblem: Possible Cause: Don't Call for ServiceUntil You:Pilot Will Not Lig

Maintenance 39Travis Industries 4030612 100-01148How this Fireplace Works• This fireplace was designed with safety as the primary concern. Many of th

4 Safety PrecautionsTravis Industries 4030612 100-01148• IF YOU SMELL GAS:* Do not light any appliance* Extinguish any open flame* Do not touch a

40 MaintenanceTravis Industries 4030612 100-01148Wiring Diagram120 Volt WiringMillivolt Wiring (for gas control valve)OrangeWhitePiezo IgniterThermopi

Safety Label 41Travis Industries 4030612 100-01148The safety (listing) label is attached to the operating tag (chained to the fireplace near the gas c

42 WarrantyTravis Industries 4030612 100-01148To register your TRAVIS INDUSTRIES, INC. 7 Year Warranty, complete the enclosed warranty card and mail i

Optional Equipment (for qualified installers only) 43Travis Industries 4030612 100-01148LP Conversion InstructionsInstall the conversion kit prior to

44 Optional Equipment (for qualified installers only)Travis Industries4030612 100-011483 Follow the directions below to replace the orifice.aSlide t

Optional Equipment (for qualified installers only) 45Travis Industries 4030612 100-011485 Install the logs andembers.6 Replace glass andface.7 Remove

46 Optional Equipment (for qualified installers only)Travis Industries4030612 100-01148Firebox InteriorWARNING Turn off gas to the appliance and mak

Optional Equipment (for qualified installers only) 47Travis Industries 4030612 100-011483 Install the liner following the directions below.(a) Tilt t

48 IndexTravis Industries 4030612 100-01148Approved Vent Configurations...16Adjusting the Blower Speed...

Safety Precautions 5Travis Industries 4030612 100-01148• Do not place clothing orother flammable items on ornear the heater. Becausethis heater can b

6 Features and SpecificationsTravis Industries 4030612 100-01148Features:- Works During Power Outages (millivolt system)- High Efficiency- Optional Th

Installation (for qualified installers only) 7Travis Industries 4030612 100-01148Installation Warnings:• Failure to follow all of the requirements ma

8 Installation (for qualified installers only)Travis Industries 4030612 100-01148Installation OverviewSee the section "Termination Requirements&

Installation (for qualified installers only) 9Travis Industries 4030612 100-01148Fireplace Placement RequirementsMinimum Framing DimensionsThe firepl