Avalon 700 Spezifikationen PDF herunterladen (Seite 39)

ADDENDUM PAGE 39

ADDENDUM #1 Altitude Considerations

This heater has been tested at altitudes ranging from sea level to 8,000 feet (2,400 M). In this testing

we have found that the fireplace, with its standard orifice, burns correctly with just an air shutter

adjustment. For information on adjusting the air shutter see page 21 of this manual.

! Failure to adjust the air shutter properly may lead to improper combustion which can create a

safety hazard. Consult your dealer or installer if you suspect an improperly adjusted air shutter.

ADDENDUM #2 Class A Chimney Conversion Kit

Simpson Duravent provides a conversion kit for those wishing to use

an existing wood stove chimney to vent this direct vent stove. The

illustration below gives an overview of this type of installation. See

the instructions included with the kit for details.

! The conversion kit does not work on interior masonry chimneys.

! Do not exceed the maximum vertical rise (see the section

"Approved Vent Configurations" starting on page 9) allowable.

Remember to set the restrictor position to the correct position

(based upon the vertical rise height - see the chart on page 10).

Chimney Conversion Kit A (# 931)

Metalbestos 6" (150 mm) I.D.

Security Chimneys 6" (150 mm) I.D.

Jackes-Evans 6" (150 mm) I.D.

Hart & Cooley 6" (150 mm) I.D.

Pro-Jet 6" (150 mm) I.D.

Chimney Conversion Kit B (# 932)

Simpson Dura-Vent 6"(150 mm) I.D.

Air-Jet 6" (150 mm) I.D.

Metal-Fab 6" (150 mm) and 7" (175 mm) I.D.

Amer. Metals 6" (150 mm) & 7" (175 mm) I.D.

Metalbestos 7" (175 mm) and 8" (200 mm) I.D.

Jackes-Evans 7" (175 mm) and 8" (200 mm) I.D.

Hart & Cooley 7" (175 mm) and 8" (200 mm) I.D.

Pro-Jet 7" (175 mm) and 8" (200 mm) I.D.

Security Chimneys 8" (200 mm) I.D.

Chimney Conversion Kit C (# 933)

Simpson Dura-Vent 7" (175 mm) and 8" (200 mm) I.D.

American Metals 8" (200 mm) I.D.

Air-Jet 8" (200 mm) I.D.

Metal-Fab 8" (200 mm) I.D.

American Metals 8" (200 mm) I.D.

Each Kit Contains: Additional Equipment:

Retro Connector 4" Flex (#711 or U.L. 1777)

Retro Vertical Top Termination (#991)

Co-Axial Sections

Type A Chimney

Simpson Duravent Direct

Vent Pipe Sections

(use adjustable section)

Screw the Retro

Vertical Top to the

Flex Pipe

Retro Vertical Top

(screw to chimney)

Screw the Retro

Connector to the

Flex Pipe

Retro Connector

(screw to chimney)

4" (100 mm)

Aluminum Flex

Pipe

Cut the Flex Pipe to

the chimney height

plus 3" (75 mm)

ADDENDUM #3 Interior

Masonry Chimney Conversions

¥ Follow the requirements and use the

equipment listed in the illustration to

the right to install this appliance into

an interior masonry chimney.

¥ Maximum vertical rise is 30'

¥ Minimum vertical rise is 10'

¥ Use the following restrictor positions:

Position 7 for heights between 10' (3

M) and 24' (7.3 M)

Position 5 for heights between 24' (7.3

M) and 30' (9.1 M)

NOTE: these restrictor positions are

based upon lab tests. The ideal

restrictor position may vary slightly.

The entire chimney system

must be air-tight. Make sure to

seal the flashing, clean-out,

and thimble connection, and to

inspect the chimney.

#711 Flex Liner

(4Ó dia.)

(or other UL 1777

Gas Liner)

Co-Axial

Straight

Lengths

#991 High

Wind

Termination

#990 90¡ Elbow

Flashing

(included in

#934 Masonry

Conversion Kit

Make sure the coaxial pipe

maintains a 1Ó clearance to any

combustible. The vent must be

sealed air-tight.

High-Temp.

Silicone

Connector with

Cover (included

in #934

Masonry

Conversion Kit

1 2 ... 34 35 36 37 38 39 40

Kommentare zu diesen Handbüchern

Keine Kommentare

Avalon 700 Spezifikationen Seite 39

Kommentare zu diesen Handbüchern