Avalon H Series Wartungshandbuch Seite 176
- Seite / 196
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Installation Instructions for 45HW & 47HW Electrified Mortise Locks
BEST ACCESS SYSTEMS
a Division of Stanley Security Solutions, Inc.
Finishing the door preparation
4
6 Determine wire gauge for power
wiring
1 Calculate the total length of the power wire run
by summing:
■ The distance from the power supply to the first
door.
■ If powering more than one door daisy-chained to
the same power supply, add the total distance of
the power runs between the doors.
2 For both 12 volt and 24 volt locks, refer to the table
below to determine the minimum wire gauge based
on the number of doors sharing the power supply and
the total length of the wire run.
7 Prepare door for wire transfer hinge
and run field wiring
1 Drill a wire access hole through the frame side of the
hinge mortise where you removed the hinge in Task 4,
Step 1 on page 3.
2 Drill holes (or pockets) for splice connectors in the
frame and door. Refer to the hinge manufacturer’s
specifications for the hole location.
3 De-burr the holes to prevent damage to the hinge
leads.
4 Run the power field wiring from the location for the
lock’s power supply to the location for the wire
transfer hinge.
Note 1: To match the lock’s wire color, use yellow for
12 volts DC power and blue for 24 volts DC power.
Note 2: To minimize lever temperature, install an
8WTCM (temperature control module) in series with the
power and ground wiring within 20 feet of the lock. Use
only one 8WTCM per lock. This module is supplied with
electrically locked (EL) functions and is optional with
electrically unlocked (EU) functions.
(Continued)
1 door 2 doors 3 doors 4 doors Min. wire gauge
250 ft. 125 ft. 75 ft. 60 ft. 18 AWG
400 ft. 200 ft. 130 ft. 100 ft. 16 AWG
600 ft. 300 ft. 185 ft. 150 ft. 14 AWG
Figure 7 Running field wiring
Door frame Door
Field wiring
- CREDITS/COPYRIGHT 2
- CONTENTS 3
- INTRODUCING THE 40H LOCK 2–1 4
- LOCK FUNCTIONS 3–1 4
- MORTISE CASE PARTS 4–1 4
- TRIM PARTS 5–1 5
- SERVICE AND MAINTENANCE 6–1 6
- 40H Series Service Manual vii 7
- TRIM PARTS 10
- SERVICE AND MAINTENANCE 11
- 48H & 49H LOCKS 11
- GETTING STARTED 13
- 45H & 47H OVERVIEW 14
- Getting Started 15
- 40H Series Service Manual 1–3 15
- 45HW & 47HW OVERVIEW 16
- 40H Series Service Manual 1–5 17
- 48H & 49H OVERVIEW 18
- 40H Series Service Manual 1–7 19
- DOCUMENTATION PACKAGE 20
- TECHNICAL SUPPORT 20
- INTRODUCING THE 40H LOCK 21
- THE ADVANTAGE OF KITS 22
- WORKING WITH TRIM KITS 23
- Introducing the 40H Lock 24
- 2–4 40H Series Service Manual 24
- TRIM ONE SIDE LOCKS 25
- 2–6 40H Series Service Manual 26
- LOCK FUNCTIONS 27
- Lock Functions 28
- 3–2 40H Series Service Manual 28
- LOCK FUNCTION QUICK REFERENCE 29
- Single-keyed 31
- 3–6 40H Series Service Manual 32
- 40H Series Service Manual 3–7 33
- Double-keyed 34
- 40H Series Service Manual 3–9 35
- Deadlocked 36
- Non-keyed 37
- Electrified 40
- MORTISE CASE PARTS 43
- A FUNCTION CASE—OFFICE LOCK 44
- A function case 45
- 4–4 40H Series Service Manual 46
- AT, C, D, INL, R, W 47
- ZD, XR function 47
- LT FUNCTION CASE—PRIVACY LOCK 48
- LT function case 49
- N FUNCTION CASE—PASSAGE LOCK 50
- N function case 51
- NX FUNCTION CASE—EXIT LOCK 52
- NX function case 53
- FUNCTION CASE—HOLDBACK LOCK 54
- CHB, RHB function 55
- AB FUNCTION CASE—OFFICE LOCK 56
- AB function case 57
- B FUNCTION CASE—ENTRANCE LOCK 58
- B function case 59
- FUNCTION CASE—ENTRANCE LOCK 60
- FUNCTION CASE—STOREROOM LOCK 60
- BA, S function case 61
- BW function case 63
- UNCTION CASE—ENTRANCE LOCK 64
- G, B5, B7, function 65
- H FUNCTION CASE—HOTEL LOCK 66
- HJ FUNCTION CASE—HOTEL LOCK 66
- H, HJ, TD function 67
- FUNCTION CASE—INTRUDER LOCK 68
- FUNCTION CASE—DORMITORY LOCK 68
- IND, T case 69
- L FUNCTION CASE—PRIVACY LOCK 70
- L function case 71
- LB FUNCTION CASE—PRIVACY LOCK 72
- LB function case 73
- TA function case 75
- AD FUNCTION CASE—DEADLOCK 76
- WD FUNCTION CASE—DEADLOCK 76
- YD FUNCTION CASE—DEADLOCK 76
- AD, WD, YD function 77
- RD function case 79
- DEL function case 81
- DEU function case 83
- WEL function case 85
- WEU function case 87
- NXEL function case 89
- NXEU function case 91
- TDEL function case 93
- TDEU function case 95
- TWEL function case 97
- TWEU function case 99
- Mortise Case Parts 100
- LEL function case 101
- LEU function case 103
- CASE ONLY LOCKS 104
- 45HCA – R – 626 – RH – 104
- 45HWCA – DEL – 626 – RH – 105
- Case only 106
- OUTSIDE TRIM KITS 108
- Available door thicknesses 109
- Qty. per kit 109
- Trim Parts 110
- 5–4 40H Series Service Manual 110
- 40H Series Service Manual 5–5 111
- INSIDE TRIM KITS 112
- 114
- 40H Series Service Manual 5–9 115
- STRIKE PACKAGES 116
- 40HST – 1 – 626 – 116
- Item Description 1 4 5 117
- LEVER SETS 118
- 40HLS – 14 – 626 – 118
- Part number 120
- FACEPLATE KITS 121
- 40HFP – 3 – 626 – 121
- REPLACEMENT SPINDLES 122
- 40HRS – 2 – 122
- Replacement 123
- SCREW KITS 124
- 40HSK – 1 – 626 – 124
- CYLINDERS AND CAMS 126
- Cylinders by door 127
- Cylinder ring 127
- Figure 5.25 Cylinder rings 128
- Figure 5.26 Cylinder cams 128
- ESCUTCHEON ASSEMBLIES 129
- J trim inside 130
- M & N trim outside 131
- M & N trim inside 132
- ROSES AND ROSE RINGS 133
- DUMMY TRIM 133
- VISUAL INDICATOR TRIM 134
- SERVICE EQUIPMENT 135
- DRIVER BITS 136
- CHANGING THE HAND 140
- Function Hub toggle position 141
- Service and Maintenance 142
- 6–4 40H Series Service Manual 142
- Changing the 143
- UNR cases 143
- TROUBLESHOOTING 145
- 6–8 40H Series Service Manual 146
- FUNCTION DESCRIPTIONS 148
- K, L, M function 149
- 48H & 49H Locks 150
- 7–4 40H Series Service Manual 150
- Figure 7.3 R function case 150
- 48H TRIM PARTS 151
- 7–6 40H Series Service Manual 152
- STRIKES AND STRIKE BOXES 153
- GLOSSARY 155
- Glossary 158
- A–4 40H Series Service Manual 158
- INSTALLATION INSTRUCTIONS 159
- Installation Instructions 160
- B–2 40H Series Service Manual 160
- Installation Instructions for 161
- 45H & 47H Mortise Locks 161
- 2 Align templates 162
- BEST ACCESS SYSTEMS 163
- 8 Install mortise case 164
- Installing the trim 165
- Finishing the installation 171
- 18 Install cores 172
- 19 Check operation 172
- 1 Identify holes 174
- Center punch and drill holes 175
- 8 Install door status switch 177
- 11 Install mortise case 179
- 22 Install cores 187
- 23 Install lock power supply 188
- 24 Make sensor connections 188
- 25 Check operation 188
- 1 Mark centerlines 189
- 2 Mark drill points 189
- 3 Install strike 189
- 7 Install core 190
- 4 Mortise and drill holes 190
- 5 Install mortise case 190
- 6 Install trim 190
- Numerics 191
- C-2 40H Series Service Manual 192
- 40H Series Service Manual C-3 193
- C-4 40H Series Service Manual 194
- 40H Series Service Manual C-5 195
- C-6 40H Series Service Manual 196
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.067 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern